The content listed below pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is extremely entertaining. You should investigate for yourself.
Installing a tub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is also a reasonably challenging task. If the old bathtub is readily accessible, the project can move rapidly; if you need to open a wall surface to get rid of the old bathtub as well as place the brand-new bathtub, the task is much harder. In either instance, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the new one. See to it you have qualified yourself for the task and fit attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to think about using one before you begin. Chances are you may need an expert plumber to make tube connections.
This post will assist you set up a new tub in your bathroom if you have already gotten a brand-new tub and also do not require to change the setup of your previous water supply pipelines.
Your devices as well as material list should consist of the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath should be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its final position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing faucets can be rather bothersome because of the limited gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a fabric prepared for the remaining water that will come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, position the bathtub in the needed position. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and also changing the feet on the bath tub up until the spirit level reviews degree.
To install taps, fit all-time low of the outermost versatile tap port to the proper supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water as well as check all joints as well as new pipework for leaks and also tighten them if needed. Fill up the tub as well as additionally check the overflow outlet as well as the normal outlet for leakages.
Lastly, fix the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the tub should wait until the bath tub has been used a minimum of once as this will certainly settle it right into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washers remain in place between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. Once the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former kind needs to be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to split an inflexible seal, causing the water to penetrate the wall in between the bath and the tiling, resulting in difficulties with wetness and also possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the activity experienced when the bathtub remains in use. The sealant can fracture rather early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub Yourself? Give a review directly below. We will be pleased to see your feelings about this page. Hoping that you come back again in the near future. Liked our blog? Please share it. Let another person locate it. Thanks for your time. Come back soon.
24/7 support? Call.